1.& Wire Rope with Compacted Outer Strands with Fibre Core
STO -TU 040-2007
Product description &
As outer strands of the rope go through crimping wheels, the strand becomes thicker & metal cross sectional area increases, strand form becomes smoother, and round, therefore the following advantages are achieved:
increased wear resistance of wires
decreased blocks groove wearing
high tensile strength
higher lateral compression strength
These advantages extend the operational life of the rope and significantly reduce operating costs.
Construction&&
6хЗ6 (1+7+7/7+14)+&FC&
Technical characteristics
Diameter, mm
Weight 1000&m, kg
Minimum breaking load, kN
2.& 8 Strand Rope with Compacted Outer Strands
STO -TU 043-2007
Product description &
The ropes are applied for hoisting at &Р&Н 2800 type excavators
As outer strands of the rope go through crimping wheels, the strand becomes thicker & metal cross sectional area increases, strand form becomes smoother, and round, therefore the following advantages are achieved:
increased wear resistance of wires
decreased blocks groove wearing
high tensile strength
higher lateral compression strength
Organic fillers (OF)&inside the rope serve as additional lubrication source which enables to protect the core from corrosion and reduce friction between rope core and outer strands.
These advantages extend the operational life of the rope and significantly reduce operating costs.
Construction &
8х37(1+6; 6+12+12) + 8 OF + 8х7(1+6) + 6х7(1+6) + 1х7(1+6)
Technical characteristics
Diameter, mm
Weight 1000&m, kg
Aggregate breaking force, kN&
The ropes of 1670 N/mm2&grade are manufactured from uncoated wire of the following grades: 1570 N/mm2&&& outer layer 1770 N/mm2&&& the rest of the wires
Due to the use of a lower grade wire in the outer layer of strands wire deformation takes place,&and &the contact area of wire with a block groove increases. It all results in less abrasive wear of the wires as well as the block grooves.
3.& 8 Strand Rope With Compacted Outer Strands
STO -TU 044-2007
Product description &
The ropes are applied for hoisting at Р&Н 2800 type excavators
As outer strands of the rope go through crimping wheels, the strand becomes thicker & metal cross sectional area increases, strand form becomes smoother, and round, therefore the following advantages are achieved:
increased wear resistance of wires
decreased blocks groove wearing
high tensile strength
higher lateral compression strength
Organic fillers (OF) inside the rope serve as additional lubrication source which enables to protect the core from corrosion and reduce friction between rope core and outer strands.
These advantages extend the operational life of the rope and significantly reduce operating costs.
Construction &
8х37(1+6; 6+12+12) + 8&OF + 8х7(1+6) + 6х7(1+6) + 1х7(1+6)
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Aggregate breaking force, kN
The ropes of 1670 N/mm2&grade are manufactured from uncoated wire
&4.& Rope for Anchorage Manufacture
STO -TU 048-2007
Product description &
Applied for manufacturing of deep burial anchors & mining rock fixing
Construction &
6х7(1+6) +1х7(1+6)
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Aggregate breaking force, kN
5.& Drilling Rope with Combined Core
STO -TU 049-2007
Product description &
These wire ropes have a combined three-wire core and three organic fillers and offer a set of technological advantages compared to ropes manufactured according to GOST 16853-88: increased wear resistance and reduced impact load on the rope.
Basic advantages of ropes with compacted outer strands TU049 (type 2) are: high tensile strength, increased abrasive resistance of strand wires and rope strands, reduced wear of blocks and drums due to the increased area of contact with the rope bearing surface.
These advantages extend the operational life of the rope and significantly reduce operating costs.
Construction &
Type&1& &6х26(1+5+5/5+10)+3х19(1+6+6/6)+3 organic fillers (OF)&witho
Type&2& &6х26(1+5+5/5+10)+3х19(1+6+6/6)+3 OF&with compacted outer strands.
Technical characteristics
Diameter, mm
Weight1000&m, kg
Minimum breaking load, kN
Weight1000&m, kg
Minimum breaking load, kN
6.& 8 Strand Rope
STO -TU 051-2007
Product description &
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves.
As outer strands of the rope go through crimping wheels, the strand becomes thicker & metal cross sectional area increases, strand form becomes smoother, and round, therefore the following advantages are achieved:
increased wear resistance of wires
decreased blocks groove wearing
high tensile strength
higher lateral compression strength
These advantages extend the operational life of the rope and significantly reduce operating costs.
Construction&&
Type&1&-&8х25(1+6; 6+12) + 6х17(1+8+8) + 1х17(1+8+8)
Type&2 -&8х26(1+5+5/5+10) + 6х17(1+8+8) + 1х17(1+8+8)&with compacted outer strands
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, kN
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, kN
&7.& 8 Strand Rope
STO -TU 052-2008
Product description &
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves.
Organic fillers&inside the rope serve as additional lubrication source which enables to protect the core from corrosion and reduce friction between rope core and outer strands.
These advantages extend the operational life of the rope and significantly reduce operating costs.
Construction &
8х36(1+7+7/7+14) + 6х19 (1+9+9) + 1х19 (1+9+9)
Type 1&- without organic fillers.&
Type 2&- with 8 organic fillers between the metal core and outer strands
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
&8.& 8 Strand Rope with Compacted Outer Strands
STO -TU 053-2008
Product description &
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves.
The strand becomes thicker & metal cross sectional area increases, strand form becomes smoother, and round, therefore the following advantages are achieved:
increased wear resistance of wires
decreased blocks groove wearing
high tensile strength
higher lateral compression strength
Organic fillers inside the rope serve as additional lubrication source which enables to protect the core from corrosion and reduce friction between rope core and outer strands.
These advantages extend the operational life of the rope and significantly reduce operating costs.
Construction &
8х36(1+7+7/7+14) + 6х19 (1+9+9) + 1х19 (1+9+9)
Type 1&- with com
Type 2&- with compacted outer strands and&8 organic fillers between the external and internal layers of the rope
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
&9.& Wire Rope with Compacted Outer Strands
STO -TU 057-2008
Product description &
As outer strands of the rope go through crimping wheels, the strand becomes thicker & metal cross sectional area increases, strand form becomes smoother, and round, therefore the following advantages are achieved:
increased wear resistance of wires
decreased blocks groove wearing
high tensile strength
higher lateral compression strength
Organic fillers inside the rope serve as additional lubrication source which enables to protect the core from corrosion and reduce friction between rope core and outer strands.
These advantages extend the operational life of the rope and significantly reduce operating costs.
Construction &
6хЗ6(1+7+7/7+14) + 6х19(1+9+9) + 1х19(1+9+9)
Type 1 - with compacted outer strands
Type 2 - with compacted outer strands and 6 organic fillers between the external and internal layers of the rope
Technical characteristics
Diameter, mm
Weight 1000 m, kg
Minimum breaking load, kN
The ropes of 1670 N/mm2&grade are manufactured from uncoated wire of the following grades: 1570 N/mm2&&& outer layer 1770 N/mm2&&& the rest of the wires
Due to the use of a lower grade wire in the outer layer of strands wire deformation takes place,&and &the contact area of wire with a block groove increases. It all results in less abrasive wear of the wires as well as the block grooves.
10. Wire Rope
STO -TU 059-2008
Product description &
LK-Z type ropes are applied almost in a wide however they should not be exposed to hostile environment conditions. The ropes have thin filling wires which are non-corrosion-resistant and thus should not bear hostile environment influence.
In comparison with the standard ropes GOST 7667-80, these ropes are characterized by better flexibility and higher tensile strength.
Construction &
6х29(1+7; 7+14) + 6х7(1+6) + 1х7(1+6)
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, kN
&11. Multistrand Rope
STO -TU 061-2008
Product description&&
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves. Opposite lay direction of external and internal strand layers prevents the rope from rotating around its axis
These advantages extend the operational life of the rope and significantly reduce operating costs.
Construction
18х7(1+6) + 5х7(1+6)/5х7(1+6) + 5х7(1+6) +&1х7(1+6)
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
Ropes are manufactured from:
uncoated wire, grade1770 N/mm2&- 2160 N/mm2
galvanized wire, grade 1770 N/mm2&- 1960 N/mm2
&12. Ground Wire for Overhead Power Transmission Lines
STO -TU 062&2008
Product description &
Intended to be hung up on power transmission lines as&protection from direct ightening strikes
Construction &
1х36 (1+7+7/7+14)
Manufactured from galvanized wire with a Heavy Zinc Coating
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Aggregate breaking force, kN
&13. Multistrand Rope
STO -TU 064-2008
Product description &
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves. Opposite lay direction of external and internal strand layers prevents the rope from rotating around its axis
These advantages extend the operational life of the rope and significantly reduce operating costs.
Construction
12х7(1+6) + 4х7(1+6)/4х7(1+6) + 4х7(1+6)
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
Ropes are manufactured from:
uncoated wire, grade1770 N/mm2&- 2160 N/mm2&
galvanized wire, grade 1770 N/mm2&- 1960 N/mm2
&14. Drilling Rope
STO -TU 068-2008
Product description &
Wire rope with a combined three-wire core and three organic fillers&offer a set of technological advantages compared to GOST 16853-88: increased wear resistance, high flexibility and reduced impact load on the rope.
These advantages extend the operational life of the rope and significantly reduce operating costs.
Construction
6х26 (1+5+5/5+10)
Type 1 - without compacted outer strands
Type 2 - with compacted outer strands
Fibre (FC) or metal core (MC)&ropes can be manufactured
Technical characteristics
Type 1 - without compacted outer strands
&Weight&1000 m, kg
Minimal breaking load, kN
Weight&1000 m, kg
Minimal breaking load, kN
Type 2 - with compacted outer strands
Diameter, mm
&Weight&1000 m, kg
Minimal breaking load, kN
Weight&1000 m, kg
Minimal breaking load, kN
&15. 8 Strand Drilling Rope
STO -TU 072-2009
Product description
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves.
These advantages extend the operational life of the rope and significantly reduce operating costs.
Construction
8х17 (1+8+8) + 6х19 (1+9+9) + 1х19(1+9+9)
Technical characteristics
Diameter, mm
Weight 1000 m, kg
Minimum breaking load, kN
&16. Wire Rope with Compacted Outer Strands
STO -TU 090-2010
Product description &
As outer strands of the rope go through crimping wheels, the strand becomes thicker & metal cross sectional area increases, strand form becomes smoother, and round, therefore the following advantages are achieved:
increased wear resistance of wires
decreased blocks groove wearing
high tensile strength
higher lateral compression strength
These advantages extend the operational life of the rope and significantly reduce operating costs.
Construction
6х36 (1+7+7/7+14) + 7х7 (1+6)&&
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, kN
&17. Wire Rope with Compacted Outer Strands
STO -TU 091-2010
Product description
As outer strands of the rope go through crimping wheels, the strand becomes thicker & metal cross sectional area increases, strand form becomes smoother, and round, therefore the following advantages are achieved:
increased wear resistance of wires
decreased blocks groove wearing
high tensile strength
higher lateral compression strength
Organic fillers inside the rope serve as additional lubrication source which enables to protect the core from corrosion and reduce friction between rope core and outer strands.
Polymer material between the metal core and the outer strands protects the core from corrosion and decreases wire wear caused by strand friction&on the core
These advantages extend the operational life of the rope and significantly reduce operating costs.
Construction&&
6хЗ6(1+7+7/7+14) + 6х7(1+6) + 1х7(1+6)
Type 1 - with compacted outer strands
Type 2 - with compacted outer strands and 6 organic fillers between the external and internal layers of the rope
Type 3 - with compacted outer strands and polymeric filling between the metal core and outer strands
Technical characteristics
Diameter, mm
Weight 1000 m, kg
Minimum breaking load, kN
The ropes of 1670 N/mm2&grade are manufactured from uncoated wire of the following grades: 1570 N/mm2&& outer layer 1770 N/mm2&&& the rest of the wires
Due to the use of a lower grade wire in the outer layer of strands wire deformation takes place, and &the contact area of wire with a block groove increases. It all results in less abrasive wear of the wires as well as the block grooves.
&18. Aircraft Rope
GOST 2172-80
Designation
Are applied in airplane and helicopter control systems
Construction
6х7(1+6)+1х7(1+6)
6х19(1+6+12)+1х19(1+6+12)
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, N
Designation
6x7(1+6)+1x7(1+6)
6x19(1+6+12)+1x19(1+6+12)
&19. LK-R (Warrington) Type Rope with Fibre Core
GOST 2688-80
Product description &
LK-R (Warrington) type ropes are suitable in hostile environment conditions ideal when used outdoors and exposed to intensive alternative bending. High structural strength of these ropes (wires of different diameters in the outer layer of a strand) provides effective use in strenuous conditions.
Construction &
6х19 (1+6+6/6)+ FC
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load,& kN
&20. Spiral Rope
GOST 3062-80
Product description &
Spiral ropes are characterized by the high content of filling in the rope cross section with metal, which specifies minimal elastic and permanent elongations in use, the result being application in a multitude of uses.
Construction &
1х7 (1+6)
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, N
&21. Spiral Rope Type TK (Standard)
GOST 3063-80
Product description &
Spiral ropes are characterized by the high content of filling in the rope cross section with metal, which specifies minimal elastic and permanent elongations in use, the result being application in a multitude of uses.
Construction &
1х19 (1+6+12)
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, N
&22. Spiral Rope Type TK (Standard)
GOST 3064-80
Product description &
Spiral ropes are characterized by the high content of filling in the rope cross section with metal, which specifies minimal elastic and permanent elongations in use, the result being application in a multitude of uses.
Construction &
1х37 (1+6+12+18)
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, N
&23. LK-O (Seal) Type Rope With Metal Core
GOST 3066-80
Product description &
LK-O (Seal) type ropes demonstrate stable operation high abrasive wear conditions due to the increased diameter of wires in the upper layer. Increased blocks and drums diameter is required for their normal running.
Construction &
6х7 (1+6)+1х7 (1+6)
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, N
&24. TK (Standard) Type Rope with Metal Core
GOST 3067-88
Product description &
TK (Standard)&type ropes are applied in strenuous operation conditions, where alternating bendings and pulsating loads are insignificant or absent.
Construction&
6х19 (1+6+12)+1х19 (1+6+12)
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, N
&25. TK (Standard) Type Rope with Metal Core
GOST 3068-88
Product description &
TK (Standard)&type ropes are applied in strenuous operation conditions, where alternating bendings and pulsating loads are insignificant or absent.
Construction &
6x37(1+6+12+18) + 1x37(1+6+12+18)
Technical characteristics
Diameter, mm
Weight 1000 m, kg
Aggregate breaking force, kN
&26. LK-O (Seal) Type Rope with Fibre Core
GOST 3069-80
Product description &
LK-O (seal)&type ropes demonstrate stable operation in high abrasive wear conditions due to the increased diameter of wires in the upper layer. Increased blocks and drums diameter is required for their normal running.
Construction &
6х7 (1+6)+ FC
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, N
&27. TK (Standard) Type Rope with Fibre Core
GOST 3070-88
Product description &
TK (Standard)&type ropes are applied in strenuous operation conditions, where alternating bendings and pulsating loads are insignificant or absent
Construction &
6х19 (1+6+12)+&FC
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, N
&28. TK (Standard) Type Rope with Fibre Core
GOST 3071-88
Product description &
TK (Standard)&type ropes are applied in strenuous operation conditions, where alternating bendings and pulsating loads are insignificant or absent
Construction &
6х37(1+6+12+18)+ FC
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, N
&29. LK-O (Seal) Type Rope with Fibre Core
GOST 3077-80
Product description &
LK-O (Seal)&type ropes demonstrate stable operation in high abrasive wear conditions due to the increased diameter of wires in the upper layer. Increased blocks and drums diameter is required for their normal running.
Construction &
6х19 (1+9+9)+FC
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, N
&30. Wire Rope with Fibre Core
GOST 3079-80
Construction &
6х37 (1+6+15+15)+FC
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, N
&31. LK-O (Seal) Type Rope with Metal Core
GOST 3081-80
Product description &
LK-O (Seal) type ropes demonstrate stable operation in high abrasive wear conditions due to the increased diameter of wires in the upper layer. Increased blocks and drums diameter is required for their normal running.
Construction &
6х19 (1+9+9)+7х7(1+6)
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, N
&32. LK-RO (Warrington-Seal) Type Rope with Fibre Core
GOST 3083-80
Product description &
Due to its 7 fibre cores, the rope has &excellent flexibility, accordingly &a rope of this kind can be successfully used for towing and mooring operations for sea and river transport.
Construction &
6х30 (0+15+15)+7 FC
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, N
&33. Triangular Strand Rope
GOST 3085-88
Product description &
Triangular strand ropes are characterized by high structural stability, high fill factor and large bearing surface.
The use of these ropes is especially efficient when there is a heavy end load and severe abrasive wear.
Construction &
6x30(6+12+12)+ FC
Type&1 -&Strand&core is manufactured from wire with tensile strength corresponding to the rope grade.
Type&2&-&Strand&core is manufactured from wire with tensile strength not higher than 1370 N/mm2
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Aggregate breaking force, kN
&34. Multistrand Rope
GOST 3088-80
Product description &
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves.
Opposite lay direction of external and internal strand layers prevents the rope from rotating around its axis.
These advantages allow to extend the operation life of the rope and significantly reduce operating costs
Construction &
18х19 (1+6+6/6) + FC
Technical characteristics
Diameter, mm
Weight1000&m, kg
Minimum breaking load, kN
&35. Triple-lay Type Rope
GOST 3089-80
Product description &
Due to the great number of strands and fibre core, triple-lay ropes are highly flexible
Construction &
6х7х19 (1+6+6/6)+FC
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, N
&36. Locked Rope with One Layer of Z-shaped Wire
GOST 3090-73
Product description &
Locked ropes are characterized by:
A high rate of rope cross section metal filling which specifies minimal elastic and permanent elongations at exploitation
maximum bearing surface
shaped outer wire retains its place within the rope at breakage.
Technical characteristics
A rope with a single layer of Z-shaped wire and ТК type core 1+6+12 or 1+6+12+18 is manufactured from bright or galvanized steel wire.
Diameter, mm
Weight&1000 m, kg
Aggregate breaking force, kN
&37. LK-Z (Filler) Type Rope With Fibre Core
GOST 7665-80
Product description &
LK&Z&(Filler) type ropes are applied almost in all the industries, nevertheless they should not be applied in the hostile environment conditions. They have thin filling wires which are non-corrosion-resistant and thus should not bear hostile environment influence.
Construction &
6х25 (1+6;6+12)+FC
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, N
&38. LK-Z (Filler) Type Rope with Metal Core
GOST 7667-80
Product description &
LK&Z (Filler)&type ropes are applied almost in all the industries, nevertheless they should not be applied in the hostile environment conditions. They have thin filling wires which are non-corrosion-resistant and thus should not bear hostile environment influence.
Construction &
6х25 (1+6;6+12) + 7х7 (1+6)
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, N
&39. LK-RO (Warrington-Seal) Type Rope with Fibre Core
GOST 7668-80
Product description &
LK-RO&(Warrington-Seal) type ropes are characterized by a larger&number of wires in the strand and resulting in&high flexibility. Wires of a larger diameter in the outer layer of the rope provides its successful application under conditions of an abrasive&and corrosive environment.
Construction &
6х36 (1+7+7/7+14)+FC
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, N
&40. LK-RO (Warrington-Seal) Type Rope with Metal Core
GOST 7669-80
Product description &
LK-RO&(Warrington-Seal) type ropes are characterized by a larger number of wires in the strand and resulting in high flexibility. Wires of a larger diameter in the outer layer of the rope provide its successful application under conditions of an abrasive and corrosive environment.
Construction &
6х36 (1+7+7/7+14)+7х7(1+6)
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, N
&41. Locked Rope with One Layer of V-shaped and One Layer of Z-shaped Wire
GOST 7675-73
Product description&&
Locked ropes are characterized by:
A high rate of rope cross section metal filling which specifies minimal elastic and permanent elongations at exploitation
maximum bearing surface
shaped outer wire retains its place within the rope at breakage.
Technical characteristics
Rope with one layer of Z-shaped, one layer of V-shaped wire and TK type core 1+6+12 or 1+6+12+18 is manufactured from bright or galvanized wire
Diameter, mm
Weight&1000&m, kg
Aggregate breaking force, kN
&42. Locked Rope with Two Layers of V-shaped and One Layer of Z-shaped Wire
GOST 7676-73
Product description&&
Locked ropes are characterized by:
a high rate of rope cross section metal filling which specifies minimal elastic and permanent elongations at exploitation
maximum bearing surface
shaped outer wire retains its place within the rope at breakage.
Technical characteristics
Rope with one layer of Z-shaped, two layers of V-shaped wire and TK type core 1+6+12 or 1+6+12+18 or 1+6+12+18+24 is manufactured from bright or galvanized wire
Diameter, mm
Weight&1000&m, kg
Aggregate breaking force, kN
&43. Multistrand Rope 18x7
GOST 7681-80
Product description &
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and simultaneously demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves.
Opposite lay direction of external and internal strand layers prevents the rope from rotating around its axis.
These advantages extend the operational life of the rope and significantly reduce operating costs
Construction &
18х7 (1+6) + FC
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, kN
&44. LK-R (Warrington) Type Rope with Metal Core
GOST 14954-80
Product description &
LK-R (Warrington) type ropes are suitable in hostile environment conditions ideal when used outdoors and exposed to intensive alternative bending. High structural strength of these ropes (wires of different diameters in the outer layer of a strand) provides &effective use in strenuous conditions.
Construction &
6х19 (1+6+6/6)+7х7 (1+6)
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, N
&45. Multistrand Rope
GOST 16827-81
Product description &
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves.
Opposite lay direction of external and internal strand layers prevents the rope from rotating around its axis.
These advantages extend the operational life of the rope and significantly reduce operating costs.
Construction
12х36(1+7+7/7+14) + 6х36(1+7+7/7+14) + FC
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, kN
&46. Multistrand Rope
GOST 16828-81
Product description &
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves.
Opposite lay direction of external and internal strand layers prevents the rope from rotating around its axis.
These advantages extend the operational life of the rope and significantly reduce operating costs.
Construction&&
12х7(1+6) + 6х19(1+6+6/6) + FC
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, kN
&47. Drilling Rope
GOST 16853-88
Product description &
Applied in Oil and Gas industry as calf lines
Construction &
6х31 (1+6+6/6+12)+&FC (fibre core)
6х31 (1+6+6/6+12) + 7х7 (1+6)
Technical characteristics
Diameter, mm
Weight&1000&m, kg
Minimum breaking load, kN
6х31 (1+6+6/6+12) + FC
6х31 (1+6+6/6+12) + 7х7
&48. Locked Rope with Two Layers of Z-shaped Wire
GOST 18901-73
Product description &
Locked ropes are characterized by:
a high rate of rope cross section metal filling which specifies minimal elastic and permanent elongations at exploitation
maximum bearing surface
shaped outer wire retains its place within the rope at breakage.
Technical characteristics
Rope with two layers of Z-shaped wire and TK type core 1+6+12 or 1+6+12+18 is manufactured from bright or galvanized wire
Diameter, mm
Weight&1000&m, kg
Aggregate breaking force, kN
&49. Pulse Tube
Designation
Is applied in the gas and oil industry as a part of an equipment system for measured reagent feeding into the well.
The main advantages of reagent measured infeed:
Decrease in the frequency of repairs
Decrease in the cleaning frequency
High accuracy of the reagent (equipment allows to monitor reagent&s heating until a certain temperature and control over its concentration)
Automatic reagent&s infeed
Decrease in well operating costs
Product description
A pulse tube is a steel wire rope with a tube metal core in the form of thin-wall stainless steel tube, which has a double-braided steel wire protection from mechanical damages.
Out of the unit through continuous pipe-line infeed, reagent flows to the deep-well pump service area, as well as into the annular space. In the course of the oil extraction, the reagent dissolves paraffin wax contained in the oil, promoting an increase in the operational life of the equipment.
Technical characteristics
Diameter, mm
&Weight&1000 m, kg
Minimum breaking load, kN
wire according to GOST&7372-79
wire according to GOST&3282-74
Rope construction 1х31(steel tube +14+17)
Rope construction 1х36(steel tube +18+18)
&50. Spiral Rope
DIN 3052 / DIN EN 3
Product description &
Spiral ropes are characterized by the high factor of filling in the rope cross section with metal, which specifies minimal elastic and permanent elongations when using, that is why it is reasonable to apply such ropes as all kinds of strains.
Construction &
1х7 (1+6)
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
&51. Spiral Rope
DIN 3053 / DIN EN 3
Product description &
Spiral ropes are characterized by the high factor of filling in the rope cross section with metal, which specifies minimal elastic and permanent elongations when using, that is why it is reasonable to apply such ropes as all kinds of strains.
Construction&&
1х19 (1+6+12)
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
&52. Seal (S) Type Rope
DIN 3055 / DIN EN 3
Product description &
Seal&type ropes demonstrate stable operation in high abrasive wear conditions due to the increased diameter of wires in the upper layer. Increased blocks and drums diameter is required for their normal running.
Construction&&
6х7 (1+6)
Fibre (FC) or metal core (MC)&ropes can be manufactured
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
Weight&1000 m, kg
Minimum breaking load, kN
&53. Filler (F) Type Rope
DIN 3057 / DIN EN 3
Product description &
Filler& type ropes are applied almost in all the industries, nevertheless they should not be applied in the hostile environment conditions.
They have thin filling wires which are non-corrosion-resistant and thus should not bear hostile environment influence.
Construction&&
6х25 (1+6;6+12) (F)
Fibre (FC) or metal core (MC)&ropes can be manufactured
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
Weight&1000 m, kg
Minimum breaking load, kN
&54. Seal (S) Type Rope
DIN 3058 / DIN EN 3
Product description &
Seal&type ropes demonstrate stable operation in high abrasive wear conditions due to the increased diameter of wires in the upper layer. Increased blocks and drums diameter is required for their normal running.
Construction &
6х19 (1+9+9)& (S)
Fibre (FC) or metal core (MC)&ropes can be manufactured
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
Weight&1000 m, kg
Minimum breaking load, kN
&55. Warrington (W) Type Rope
DIN 3059 / DIN EN 3
Product description &
Warrington type ropes should be applied in hostile environment conditions and when used outdoors and exposed to intensive alternative bending. High structural strength of these ropes (wires of different diameters in the outer layer of a strand) provides their effective use in strenuous conditions.
Construction &
6х19(1+6+6/6) (W)
Fibre (FC) or metal core (MC)&ropes can be manufactured
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
Weight&1000 m, kg
Minimum breaking load, kN
&56. Standard (M) Type Rope
DIN 3060 / DIN EN 3
Product description &
Standard type ropes are applied in strenuous operation conditions, where alternating bendings and pulsating loads are insignificant or miss
Construction &
6х19 (1+6+12) (M)
Fibre (FC) or metal core (MC)&ropes can be manufactured
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
Weight&1000 m, kg
Minimum breaking load, kN
&57. 8 Strand Rope of Seal (S) Type
DIN 3062 / DIN EN 3
Product description &
Is applied as ropes for lift equipment and& power-hoisting equipment.
Seal&type ropes demonstrate stable operability in high abrasive wear conditions due to the increased diameter of wires in the upper layer. Increased blocks and drums diameter is required for their normal running.
Construction &
8х19 (1+9+9) (S)
Fibre (FC) or metal core (MC)&ropes can be manufactured
It is possible to &produce ropes for lift equipment from wires of two marking groups: outer wires& of marking group 1370 N/mm2, inner wires of strand & 1770 N/mm2
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
Weight&1000 m, kg
Minimum breaking load, kN
&58. 8 Strand Rope of Warrington (W) Type
DIN 3063 / DIN EN 3
Product description &
Is applied as ropes for lift equipment and& power-hoisting equipment.
Warrington type&ropes should be applied in hostile environment conditions and when used outdoors and exposed to intensive alternative bending. High structural strength of these ropes (wires of different diameters in the outer layer of a strand) provides their effective use in strenuous conditions.
Construction&&
8х19 (1+6+6/6) (W)
Fibre (FC) or metal core (MC)&ropes can be manufactured
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
Weight&1000 m, kg
Minimum breaking load, kN
&59. Warrington-Seal (WS) Type Rope
DIN 3064 / DIN EN 3
Product description &
Warrington-Seal type ropes are characterized by comparatively big number of wires in strands and consequently high flexibility. Wires of bigger diameter in the outer layer of the rope provide its successful application under conditions of abrasive damage and corrosive environment
Construction &
6х36 (1+7+7/7+14) (WS)
Fibre (FC) or metal core (MC)&ropes can be manufactured
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
Weight&1000 m, kg
Minimum breaking load, kN
&60. Standard (M) Type Rope
DIN 3066 / DIN EN 3
Product description &
Standard type ropes are applied in strenuous operation conditions, where alternating bendings and pulsating loads are insignificant or miss.
Construction &
6х37 (1+6+12+18) (M)
Fibre (FC) or metal core (MC)&ropes can be manufactured
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
Weight&1000 m, kg
Minimum breaking load, kN
&61. Multistrand Rope 18x7
DIN 3069 / DIN EN 3
Product description &
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves. Opposite lay direction of external and internal strand layers prevents the rope from rotating around its axis.
These advantages extend the operational life of the rope and significantly reduce operating costs
Construction &
18х7 (1+6) +&FC (fibre core)
18х7 (1+6) + 1х7 (1+6) (metal core)
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
Weight&1000 m, kg
Minimum breaking load, kN
&62. Multistrand Rope 36Mx7
DIN 3071 / DIN EN 3
Product description
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves. Opposite lay direction of external and internal strand layers prevents the rope from rotating around its axis.
These advantages extend the operational life of the rope and significantly reduce operating costs
Construction&&
18х7 (1+6) + 12х7 (1+6) + 6х7 (1+6) +&FC (fibre core)
18х7 (1+6) + 12х7 (1+6) + 6х7 (1+6) + 1х7 (1+6) (metal core)
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
Weight&1000 m, kg
Minimum breaking load, kN
&63. 8 Strand Rope of Warrington-Seal (WS) Type
Product description &
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves.
These advantages extend the operational life of the rope and significantly reduce operating costs
Construction&&
8х26(1+5+5/5+10) (WS)
Fibre (FC) or metal core (MC)&ropes can be manufactured
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
Weight&1000 m, kg
Minimum breaking load, kN
&64. Locked Rope with OMEGA-shaped Wires
TU 14-171-16-2001
Product description &
Locked ropes are characterized by:
high rate of rope cross section metal filling which specifies minimal elastic and permanent elongations at exploitation
maximum bearing surface
shaped outer wire ability to keep its place within the rope at breakage.
Technical characteristics
A rope with one layer of&OMEGA-shaped wire, one layer of V-shaped wire and TK type core. Manufactured from galvanized wire
Diameter, mm
Weight 1000 m, kg
Aggregate breaking force, kN
&65. Wire Rope
Product description &
The ropes of 1670 N/mm2&grade are manufactured from uncoated wire of the following grades: 1570 N/mm2&&& outer layer 1770 N/mm2&&& the rest of the wires
Due to the use of a lower grade wire in the outer layer of strands wire deformation takes place, and &the contact area of wire with a block groove increases. It all results in less abrasive wear of the wires as well as the block grooves
Construction &
6хЗ6 (1+7+7/7+14) + 7х7(1+6)
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Aggregate breaking force, kN
&66. Multistrand Rope 36Mx7
TU 14-171-45-2002
Product description &
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves. Opposite lay direction of external and internal strand layers prevents the rope from rotating around its axis.
These advantages extend the operational life of the rope and significantly reduce operating costs
Construction &
18х7(1+6) + 12х7(1+6) + 6х7(1+6) +&FC
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
&67. 8 Strand Rope
TU 14-4-163-2004
Product description &
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves.
These advantages extend the operational life of the rope and significantly reduce operating costs
Construction &
Type&1 - 8х36 (1+7+7/7+14)+6х37 (1+6+12+18)+1х37 (1+6+12+18)
Type&2 -&8х36 (1+7+7/7+14)+6х36 (1+7+7/7+14)+1х36 (1+7+7/7+14)
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Aggregate breaking force, kN
&68. Wire Rope
TU 14-4-273-2002
Product description
Filler&type ropes are applied almost in a wide however they should not be exposed to hostile environment conditions. The ropes have thin filling wires which are non-corrosion-resistant and thus should not bear hostile environment influence.
Construction &
6х25(1+6; 6+12) + 7х7(1+6)
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
&69. Wire Rope for Automobiles
TU 14-4-297-85
Product description&&
Intended for manipulating a hand brake and window lifters.
Technical characteristics
Diameter, mm
Construction
Weight&1000 m, kg
Minimum breaking load, N
5х7 (1+6)+1о.с.
1х25 (3+9+13)
&6х12(3+9)+1х12(3+9)
&70. Core for Bare Wires of Power Transmission Lines
TU 14-178-462-2004
Product description&&
The core is used for manufacturing bare wires for overhead power transmission lines.
The core is a spiral rope of 1х7(1+6) or 1х19(1+6+12) construction. It is manufactured from galvanized wire according to GOST& 9850-72
Technical characteristics
Core&marking
Diameter wire, mm
Weight1000 m, kg
Breaking force of one core wire at 1%
extension, calculated according to the tension at 1% elongation and cross
section of wire&of nominal diameter (class A(B),N not less).
С 0/19-galv
С 0/18-galv
С 0/20,4-galv
С 0/24-galv
С 0/29-galv
С 0/32-galv
С 0/34-galv
С 0/39-galv
С 0/43-galv
С 0/51-galv
С 0/64-galv
С 0/66-galv
С 0/72-galv
С 0/93-galv
71. 8 Strand Wire Rope
TU 14-4-496-74
Product description &
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves.
As outer strands of the rope (type 3) go through crimping wheels, the strand becomes thicker & metal cross sectional area increases, strand form becomes smoother, and round, therefore the following advantages are achieved:
increased wear resistance of wires
decreased blocks groove wearing
high tensile strength
higher lateral compression strength
Organic fillers inside the rope serve as additional lubrication source which enables to protect the core from corrosion and reduce friction between rope core and outer strands.
These advantages extend the operational life of the rope and significantly reduce operating costs
Construction &
8х36 (1+7+7/7+14) + 7х19 (1+9+9)
Type&1 & without fiber filler.
Type&2 & 8 fiber fillers between outer and inner rope layers.
Type&3 - 8 fiber fillers between outer and inner rope layers and compacted outer strands
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
&72. 8 Strand Wire Rope
TU 14-4-721-76
Product description &
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves.
These advantages extend the operational life of the rope and significantly reduce operating costs
Construction &
8х61 (1+6; 6+12+18+18)+6х36 (1+7+7/7+14)+FC
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
&73. 8 Strand Wire Rope
TU 14-4-722-76
Product description&&
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves.
These advantages extend the operational life of the rope and significantly reduce operating costs
Construction
8х36 (1+7+7/7+14)+6х19 (1+9+9) +&FC&
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
&74. Locked Rope with Z-shaped Wires
TU 14-4-1216-82
Product description &
Locked ropes are characterized by:
high rate of rope cross section metal filling which specifies minimal elastic and permanent elongations at exploitation
maximum bearing surface
shaped outer wire ability to keep its place within the rope at breakage.
Technical characteristics
Locked rope with Z-shaped outer layer wires. Is manufactured from galvanized wire.
Diameter, mm
Weight&1000&m, kg
Construction
Aggregate breaking force, kN
1х56(1+7+7/7+14+20Z)
1х84(1+7+7/7+14+20Z+28Z)
1х116(1+7+7/7+14+20Z+28Z+32Z)
1х109(1+7+7/7+14+20Z+27Z+26Z)
1х154(1+7+7/7+14+20Z+28Z+32Z+38Z)
1х141(1+7+7/7+14+20Z+27Z+26Z+32Z)
1х198(1+7+7/7+14+20Z+28Z+32Z+38Z+44Z)
1х183(1+7+7/7+14+20Z+27Z+26Z+32Z+42Z)
1х226(1+7+7/7+14+20Z+27Z+26Z+32Z+42Z+43Z)
&75. 8 Strand Wire Rope
TU 14-4-1291-84
Product description &
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves.
These advantages extend the operational life of the rope and significantly reduce operating costs
Construction &
8х61 (1+6;6+12+18+18)+6х36 (1+7+7/7+14)+1х36 (1+7+7/7+14)
Type 1- without fiber filler&
Type 2 - with 8 fiber fillers between outer and inner rope layers
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Aggregate breaking force, kN
&76. 8 Strand Wire Rope
TU 14-4-1394-86
Product description &
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves.
These advantages extend the operational life of the rope and significantly reduce operating costs
Construction &
8х67 (1+6+6/6+12+18+18)+6х31 (1+6+6/6+12) + FC
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Aggregate breaking force, kN
&77. 8 Strand Wire Rope
TU 14-4-1502-88
Product description &
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves
These advantages extend the operational life of the rope and significantly reduce operating costs
Construction &
8х36 (1+7+7/7+14)+ 3х36 (1+7+7/7+14)+3 organic fillers
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
&78. 8 Strand Wire Rope
TU 14-4-1549-89
Product description &
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves.
These advantages extend the operational life of the rope and significantly reduce operating costs
Construction &
Type&"А" -&8х36 (1+7+7/7+14)+6х19 (1+6+6/6) + FC
Type&"Б"&-&8х36 (1+7+7/7+14)+6х19 (1+6+6/6)+1х19 (1+6+6/6)
Technical characteristics
Diameter, mm
&Weight&1000 m, kg
Minimum breaking load, kN
&79. 8 Strand Wire Rope
TU 14-4-1552-89
Product description &
Due to the increased number of strands (as compared to the 6 strand ropes) these ropes are more flexible, and at the same time, demonstrate high tensile strength and reduced friction between the outer wires of strands and the surface of block grooves.
These advantages extend the operational life of the rope and significantly reduce operating costs
Construction &
8х37 (1+12+12+12) + 3х7 (1+6); 3х37 (1+12+12+12) + FC
Technical characteristics
Diameter, mm
Weight&1000 m, kg
Minimum breaking load, kN
&80. Locked Rope With OMEGA-shaped Wires
TU 14-4-1766-94
Product description
Locked ropes are characterized by:
high rate of rope cross section metal filling which specifies minimal elastic and permanent elongations at exploitation
maximum bearing surface
shaped outer wire ability to keep its place within the rope at breakage.
Technical characteristics
Rope with one layer of&OMEGA-shaped wire, one or two layers of V-shaped wire and TK type core. Manufactured from bright wire
Diameter, mm
Weight 1000&m, kg
Aggregate breaking force, kN&
Adres: Введите адресE-mail: